DS1775
 
 
4 of 14
 
Table 2. Temperature/Data Relationships
 
S
2
6
 
2
5
 
2
4
 
2
3
 
2
2
 
2
1
 
2
0
 
MSB
MSb
 
 
UNIT = 癈
 
 
LSb
 
2
-1
 
2
-2
 
2
-3
 
2
-4
 
0
0
0
0
LSB
 
TEMPERATURE
?SPAN class="pst DS1775R7-T-R_2292811_1">C  
DIGITAL OUTPUT
BINARY
DIGITAL OUTPUT
HEX
+125
0111 1101 0000 0000
7D00h
+25.0625
0000 1010 0010 0000
1910h
+10.125
0000 1010 0010 0000
0A20h
+0.5
0000 0000 1000 0000
0080h
0
0000 0000 0000 0000
0000h
-0.5
1111 1111 1000 0000
FF80h
-10.125
1111 0101 1110 0000
F5E0h
-25.0625
1110 0110 1111 0000
E6F0h
-55
1100 1001 0000 0000
C900h
 
Thermostat Control
In its comparator operating mode, the DS1775 functions as a thermostat with programmable hysteresis, as
shown in Figure 2. When the DS1775s temperature meets or exceeds the value stored in the high
temperature trip register (T
OS
) a consecutive number of times, as defined by the configuration register, the
output becomes active and stays active until the first time that the temperature falls below the temperature
stored in the low temperature trigger register (T
HYST
). In this way, any amount of hysteresis may be
obtained. The DS1775 powers up in the comparator mode with T
OS
 = +80癈 and T
HYST
 = +75癈 and can
be used as a stand-alone thermostat (no 2-wire interface required) with those setpoints.
 
In the interrupt mode, the O.S. output first becomes active following the programmed number of
consecutive conversions above T
OS
. The fault can only be cleared by either setting the DS1775 in a
shutdown mode or by reading any register (temperature, configuration, T
OS
, or T
HYST
) on the device.
Following a clear, a subsequent fault can only occur if consecutive conversions fall below T
HYST
. This
interrupt/clear process is thus cyclical (T
OS
, clear, T
HYST
, clear, T
OS
, clear, T
HYST
, clear, etc.). Only the
first of multiple consecutive T
OS
 violations activates O.S., even if each fault is separated by a clearing
function. The same situation applies to multiple consecutive T
HYST
 events.
相关PDF资料
DS1821C+ IC THERMOMETER/STAT PROG 3-TO92
DS1825U+T&R IC THERMOMETER DIGITAL 8-USOP
DS1842N+T&R IC CURRENT MONITOR 14TDFN
DS18B20+PAR IC THERM MICROLAN PROG-RES TO-92
DS18B20Z/T&R IC THERM MICROLAN PROG-RES 8SOIC
DS2740U+T&R IC CURRENT GAUGE(15BIT) 8UMAX
DS28EA00U+T&R IC THERMOMETER 1-WIRE 8-USOP
DS3920T-001+ IC CURRENT MIRROR 5:1 SOT23-6
相关代理商/技术参数
DS1775R7+U 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1775R7-U 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1775R-U 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1776 制造商:NSC 制造商全称:National Semiconductor 功能描述:PI-Bus Transceiver
DS1776E/883 制造商:NSC 制造商全称:National Semiconductor 功能描述:PI-Bus Transceiver
DS1776J/883 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:
DS1776W/883 制造商:未知厂家 制造商全称:未知厂家 功能描述:Single 8-bit Bus Transceiver
DS1777TM 制造商:未知厂家 制造商全称:未知厂家 功能描述:4-Bit Bus Transceiver